Admission now open for 2026

Log In
Craw Security

IoT security · Penetration testing

Break Into Smart Devices Safely: IoT Pentesting Training

Most security courses stop at laptops and servers. This one goes down to circuit boards, debug ports, radio signals and firmware images, taught from the Saket and Laxmi Nagar campuses in Delhi.

Hardware + firmwareHindi & EnglishOnline or classroomFutureSkills Prime certificate
Need Help?
9513805401
Certification
FutureSkills Prime (MeitY-NASSCOM Digital Skilling Initiative)
Campuses
Saket, Laxmi Nagar (New Delhi)
Mode
Online and offline

01

What makes IoT testing different from normal pentesting

A smart camera, a wearable or a router is a small computer with a network stack, a web interface, a mobile app and often a radio, all in one cheap box. Each of those layers can fail, and a tester has to look at all of them. Many devices also ship with the same weaknesses year after year, so skilled testers often chain several minor issues into one serious compromise.

This course follows that reality. You learn to map the attack surface of a device first, then attack it layer by layer: the physical ports, the data protocols it speaks, the firmware it runs, and the apps that control it.

02

Where each layer is tested

A rough map of the device layers covered and the techniques practised against them.

LayerWhat you examineTopics from the syllabus
HardwareBoards, chips and debug interfacesAnalysing hardware, UART, I2C, SPI, JTAG
FirmwareThe code stored on the deviceFirmware reverse engineering and exploitation
ProtocolsHow devices talk to each otherMQTT, CoAP, HTTP, ZigBee, Bluetooth, LoRaWAN
RadioWireless signals in the airSoftware defined radio, ZigBee and BLE
Apps and webMobile and web control panelsMobile, web and network exploitation for IoT

03

How an IoT engagement is run

The course teaches the five standard stages of a penetration test and applies them to connected devices.

  1. 1

    Planning and reconnaissance

    Agree what is in scope and collect information about the device and its ecosystem.

  2. 2

    Scanning

    Probe services, ports and interfaces to find what is exposed.

  3. 3

    Gaining access

    Use the weaknesses found to get into the device in a controlled lab.

  4. 4

    Maintaining access

    Check whether a foothold can persist, to judge real impact.

  5. 5

    Analysis and report

    Write up findings so a manufacturer or IT team can fix them.

04

Good fit if you are

  • A network or web pentester who wants to extend into hardware
  • An embedded or firmware developer who wants to see how products get attacked
  • A SOC analyst whose company is rolling out sensors, cameras or smart building systems
  • A student of electronics or computer science looking for a niche inside security

Syllabus

What you will study, module by module

Download Syllabus
01Internet of Things A Primer
  • Introduction
  • Previous IoT Security Issues
  • Fragmentation in the Internet of Things
  • Reasons for IoT Security Vulnerabilities
  • Conclusion
02Performing an IoT Pentest
  • Introduction
  • What Is an IoT Penetration Test?
  • Attack Surface Mapping
  • Creating an Attack Surface Map
  • Structuring the Pentest
  • Conclusion
  • Action Point
03Analyzing Hardware
  • Architecture of IoT
  • The Architecture of IoT Layers
  • Analyzing Hardware
  • Conclusion
04IoT Data Protocols
  • MQTT
  • IP versus CoAP for IoT Communications
  • HTTP
  • ZigBee
  • Bluetooth
  • LoRaWAN
05Serial and Connections
  • UART Communication
  • Exploitation Using I2C and SPI
  • Digging Deep into SPI
  • How Does SPI Work?
  • Conclusion
06JTAG Debugging and Exploitation
  • Introduction
  • How to Find JTAG Port?
  • Debugging with JTAG
  • Exploiting via JTAG
  • Conclusion
07Firmware Reverse Engineering and Exploitation
  • Introduction
  • Understanding Firmware
  • Firmware Exploitation
  • What is Inside the Firmware?
  • Generate Backdoor Reverse Shell
  • Conclusion
08Exploiting Mobile Web and Network for IoT
  • Introduction
  • Mobile Application Vulnerabilities in IoT
  • Web Application Security for IoT
  • Conclusion
09Software Defined Radio
  • Introduction
  • Setting Up the Lab
  • Installing Software for SDR Research
  • SDR 101 What You Need to Know?
  • Common Terminology
  • GNU Radio for Radio Signal Processing
  • Conclusion
10Exploiting ZigBee and BLE
  • Introduction
  • ZigBee 101
  • Hardware for ZigBee
  • ZigBee Security
  • Bluetooth Low Energy
  • Conclusion

FAQ

Questions people ask before enrolling

Can an IoT device really be hacked?

Yes. Any device that connects to a network can be attacked if it ships with weak defaults, outdated firmware or exposed debug ports. Finding those gaps before an attacker does is the purpose of IoT pentesting.

Do I need electronics knowledge before joining?

Basic networking and Linux comfort are more useful than electronics. The hardware modules start from how the device architecture is laid out, so you do not need to arrive as a hardware engineer.

Which certificate do I receive?

Learners receive a certificate from FutureSkills Prime, a MeitY-NASSCOM Digital Skilling Initiative, after clearing its examination.

How many hours is the course?

Different pages in our records show different totals, so we do not quote one here. A counsellor can give you the exact hours for the batch you pick.

Is a lab included, or is it only slides?

The course includes live labs and hands-on sessions supervised by trainers, covering debugging ports, firmware work and radio analysis.

How do I get the fee?

Call +91-9513805401 and ask for the current price and next batch. Fees are confirmed by phone rather than printed on the page.

Ready to test connected devices?

Ask a counsellor about the next IoT pentesting batch, online or in Delhi.